D-link Wireless Router Dir 600 Driver Download Latest

By Anahorab

D-link Wireless Router Dir 600 Driver Download Install Update

Changing the Computer Name and Joining a Workgroup Using a power supply with a different voltage rating than the one included with the DIR will cause damage and void the warranty for this product. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate.

Environmental conditions will adversely affect wireless signal range. Receptor for the Power Adapter. Cable or DSL modem. Ethernet-enabled computer on ports This LED blinks during data transmission.

Position your devices so that the number of walls or ceilings is minimized. Screw the provided screws with the equipment to the wall or partition where the device to be placed. Place the mounting holes on the bottom of the device over the screws to mount it to the wall or partition. Connect your cables to the device. Verify the link lights on the router. If not, make sure your computer, modem, and router are powered on and verify the cable connections are correct.

Skip to page 16 to configure your router. Connect an Ethernet cable in one of the LAN ports of the router and connect it to your other router. You may now use the other three LAN ports to connect other Ethernet devices and computers.

To configure your wireless network, open a web browser and enter the IP address you assigned to the router. Section 3 - Configuration Configuration This section will show you how to configure your new D-Link wireless router using the web-based configuration utility. Web-based Configuration Utility To access the configuration utility, open a web-browser such as Internet Explorer and enter the IP address of the router Internet Setup window to quickly set up your router.

Click Internet Connection Setup Wizard, you will be directed to the first window of the wizard. Click Next to continue. Create a new password and then click Next to continue.

The default host name is the device name of the Router and may be changed. If you selected Static, enter your network settings supplied by your Internet provider. Click Connect to save your settings. Please allow minutes for rebooting. When the router has finished rebooting, the opening window will be displayed. Secondary DNS This is optional. Connection Select either Always-on, Manual, or Connect-on demand. To disable this feature, enable Auto-reconnect.

Select either Always-on, Manual, or Connect-on demand. In addition, the second step also includes an option to use a MAC address that will always be associated with the connection. The MAC address is entered manually or copied from the computer. Please print this out or record this information in a safe place and then click Save to continue.

The Router will save your new settings and reboot. When it is finished after minutes, the opening Wireless Setup window is displayed. WEP key as you Router before your wireless network adapters.

Please establish did on the Router. Your wireless signal may degrade when enabling encryption due to the added overhead. Next to Shared Secret, enter the security key. Click Save Settings to save your settings. Check the box to transfer the DNS server Relay: If unchecked, your computers will use the router for a DNS server. Refer to the next page for DHCP information. Uncheck to disable this function. Enter the Lease time in minutes. NTP synchronizes computer clock times in a network of computers.

The schedule of time when the parental control filter will be enabled. The schedule may be set to Always, which will allow the particular service to always be enabled. You may define a single port or a range of ports. You can use a comma to add multiple ports or port ranges. Network causes the measured uplink speed to be reported slightly lower than before on such connections, but gives much better results. When Connection Type is set to automatic, the automatically detected connection type is displayed here.

The schedule of time when the network filter will be enabled. Enter a beginning and ending IP address. Select the transport protocol that will be used for the filter rule.

Enter the desired port range for the filter rule. Select if you are not using any This is the default setting. Check this box to reduce the guard interval time therefore increasing the data capacity. The IP address of the packets that will take this route. The subnet of the IP address of the packets that will take this route.

Specifies the next hop to be taken if this route is used. The port number used to access the DIR If you want to save the current router configuration settings, use the Save button above. Click the Reboots button on the left side of the window to restart the Router. You can upgrade the firmware of the Router here. Make sure the firmware you want to use is on the local hard drive of the computer.

Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support site for firmware updates at http: Enter the host name of the DDNS server. Enter the username given to you by your DDNS server. Enter the password or key given to you by your DDNS server. The Ping Test is used to send Ping packets to test if a computer is on the Internet. Tick this check box if the new schedule rule applies to the full hour period.

Click the checkbox es of the type of log information Level: IP settings for the router. Wireless Displays the wireless MAC address and your View the last page of the log. View the previous page. View the next page. The traffic counter will reset if the device is rebooted.

Section 3 - Configuration Wireless The wireless client table displays a list of current connected wireless clients. This table also displays the connection time and MAC address of the connected wireless client. Section 3 - Configuration Help Click the desired hyperlink to get more information about how to use the Router. ASCII format is provided so you can enter a string that is easier to remember.

Four keys can be defined so that you can change keys easily. If you are configuring the router with a wireless adapter, you will lose connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the router.

EAP is built on a more secure public key encryption system to ensure that only authorized network users can access the network. Refer to the Networking Basics section in this manual for more information.

Select View Available Wireless Networks. It may take seconds to connect to the wireless network. If the connection fails, please verify that the WEP settings are correct. The WEP key must be exactly the same as on the wireless router.

If you are using third party software to set up Wi-Fi Protection, carefully follow the directions. When you are finished, proceed to the next section to set up the newly-configured Router.

D-link Wireless Router Dir 600 Driver Download

D-Link DIR-600 User Manual

Downloads can vary across product revisions. Please select the correct hardware revision. Once connected, you can create your own personal wireless home network to share documents, music, and photos. Based on Wireless N technology with a single antenna, the DIR achieves wireless speeds of up to Mbps and extended coverage with virtually no dead spots 1. It is compatible with newer Wireless N and widespread Wireless G technologies and is ideal for email, web browsing and file sharing in the home. Robust security The DIR supports the latest wireless security features to help prevent unauthorised access, be it from over the wireless network or from the Internet. Strong parental controls are included, that allow blocking or allowing of specific web sites completely or at certain times of the day. When enabled, the router improves your online experience, by ensuring that interactive traffic such as gaming, audio and video is prioritised over less time-sensitive traffic such as e-mail or file transfers.

D-Link DIR-600 - Wireless N 150 Home Router User Manual

D-link Wireless Router Dir 600 Driver Download

Also be sure that you have downloaded the most recent firmware version version 1. Next, you can try to either reset your network settings or power cycle your iPhone to see if it gains access to the network. You may also try and reset your router as well to try and get access set up to your iPhone 4. Be sure that you are entering the correct network passwords if you have configured WPA or WPA2 to allow access to the wireless network as well. If you still have problems connecting please contact D-Link technical support at www. Unplug the power to your DSL or Cable modem. Plug the power back into your DSL or cable modem.

0 thoughts on “D-link Wireless Router Dir 600 Driver Download

Leave a Reply

Your email address will not be published. Required fields are marked *